Logo
Get Estimate
Repair TipsLocal Guides

How to fix a dripping faucet in your McLean home


A dripping faucet wastes water and drives up your bill. Here's how to diagnose the cause, replace the cartridge, and know when to call a pro in McLean, VA.

PPlumbers McLean ·November 2026 ·9 min read
Flat lay of various tools and 'Labor Day' letters on white tiles. Perfect for Labor Day themes.

A dripping faucet in your McLean home is almost always caused by a worn rubber seal, a corroded valve seat, or a failed cartridge - and you can fix it yourself in about an hour with a screwdriver, an adjustable wrench, and a replacement part that costs between $8 and $35. The drip stops when you replace the worn component, not when you tighten the handle harder. This guide walks you through diagnosing the cause, choosing the right replacement part, and completing the repair without damaging the finish or the supply lines.

We're Plumbers McLean VA, and we've repaired thousands of faucets across McLean and Northern Virginia. Most drips we see are straightforward fixes. Here's how to handle yours.

Why is my faucet dripping?

A faucet drips because the internal sealing mechanism - a rubber O-ring, a ceramic cartridge, or a compression washer - has worn out and no longer blocks water flow completely. In McLean, the average water temperature from the Potomac-fed supply runs about 55°F, but inside your faucet, hot water can reach 120-140°F. That constant thermal cycling hardens rubber seals over time. Add Fairfax County's moderately hard water (typically 7-9 grains per gallon), and you get mineral deposits that pit valve seats and scratch ceramic discs.

Three faucet types dominate McLean homes:

  • Compression faucets - common in older homes built before 1990. They use rubber washers that compress against a seat. The washer wears flat, and the drip starts.
  • Cartridge faucets - the most common type today. A single cartridge controls both hot and cold. When the cartridge's internal seals fail, you get a drip or a handle that leaks at the base.
  • Ceramic disc faucets - found in newer construction and higher-end fixtures. Two ceramic discs slide against each other. Sediment scratches the discs, and the faucet drips.

If your faucet drips from the spout, the problem is the cartridge, washer, or disc. If it drips from under the handle, the O-rings or packing nut need attention. If it drips from the base of the spout, the spout O-ring is the culprit.

Tools and parts you'll need

Before you start, gather these items. You likely have most of them already.

  • Adjustable wrench or basin wrench (for tight spaces under the sink)
  • Phillips and flathead screwdrivers
  • Allen wrench set (many modern faucets use a set screw to hold the handle)
  • Replacement cartridge, washer, or O-ring kit - match your faucet brand and model
  • Plumber's grease (silicone-based, not petroleum)
  • White vinegar and a small brush (for cleaning mineral deposits)
  • Bucket or towel to catch residual water
  • Flashlight or headlamp

Find your faucet's brand and model number. It's usually stamped on the base of the faucet, inside the cabinet, or on the original installation paperwork. If you can't find it, take a photo of the faucet and bring it to a local hardware store - they can match the cartridge. For Moen, Delta, Kohler, and American Standard, cartridges are widely available. For imported or discontinued fixtures, you may need to order online.

How to fix a dripping faucet step by step

This procedure works for most cartridge and ceramic disc faucets. Compression faucets follow a similar pattern but use a washer and seat instead of a cartridge.

  1. Shut off the water supply. Look under the sink for the two shutoff valves - one for hot, one for cold. Turn them clockwise until they stop. If they're stuck or missing, shut off the main water valve for the house.
  2. Open the faucet to release pressure. Turn the handle to the on position and let any remaining water drain out. This prevents a surprise spray when you open the faucet body.
  3. Plug the drain. A stopper or a rag over the drain prevents small screws and springs from disappearing down the pipe.
  4. Remove the handle. Pop off the decorative cap (often marked H or C) with a flathead screwdriver. Underneath, you'll find a Phillips screw or an Allen set screw. Remove it and pull the handle straight up. If it's stuck, wiggle gently - don't force it.
  5. Remove the retaining nut or clip. Depending on your faucet, you'll see a brass nut, a plastic retaining ring, or a metal clip holding the cartridge in place. Remove it carefully.
  6. Pull out the cartridge. Use pliers if needed, but grip the cartridge body - not the stem. Note its orientation so you can install the new one the same way.
  7. Inspect and clean. Look for cracks, hardened rubber, or mineral buildup. Clean the valve seat and the inside of the faucet body with white vinegar and a small brush. Rinse and dry.
  8. Install the new cartridge. Apply a thin layer of plumber's grease to the new cartridge's O-rings. Slide it in, aligning any tabs or slots. Reinstall the retaining nut or clip.
  9. Reassemble the handle. Replace the handle, screw, and cap. Tighten snugly - don't overtighten, or you'll crack the plastic.
  10. Turn the water back on and test. Open the shutoff valves slowly. Run the faucet for 30 seconds, then shut it off and watch for drips. If it still drips, the cartridge may be seated incorrectly or the valve seat may be damaged.

If you're dealing with a faucet repair McLean VA issue that involves a corroded valve seat or a cracked faucet body, replacement parts alone won't solve it. That's when you need a plumber.

Faucet cartridge replacement: when to replace vs. clean

Cleaning a cartridge buys you a few weeks at best if the rubber seals are already hardened. Replacement is the permanent fix. Here's how to decide:

  • Clean if the faucet is less than 3 years old and the drip started suddenly after a water main flush or a period of disuse. Mineral debris may be the only issue.
  • Replace if the faucet drips constantly, if the handle feels stiff or gritty, if you see black rubber particles in the water, or if the cartridge is more than 5 years old. Cartridges are inexpensive - typically $12-$30 for major brands.
  • Replace the faucet if the body is cracked, the finish is peeling, or the valve seat is pitted beyond what a cartridge can seal. A new faucet costs $80-$250 for a quality kitchen model, plus installation if you hire a pro.

For Plumbers McLean VA in Downtown McLean, we often see older homes with original 1980s fixtures where the valve seat is too far gone for a simple cartridge swap. In those cases, we recommend a full faucet replacement - it's often cheaper than repeated repairs.

How much does dripping faucet repair cost in McLean VA?

Typical 2026 pricing in this area breaks down like this:

  • DIY repair: $8-$35 for a replacement cartridge or washer kit. Your time: 45-90 minutes.
  • Professional faucet repair: $150-$350 for a single faucet, including the part. This covers diagnosis, cartridge replacement, and testing.
  • Faucet replacement (labor only): $200-$450 if you supply the new faucet. Add $80-$250 for the faucet itself.
  • Emergency or after-hours service: $250-$500, depending on the time and complexity.

These ranges reflect McLean's market, where older homes and higher-end fixtures can add complexity. A standard Moen kitchen faucet cartridge swap is on the low end. A three-hole Roman tub faucet with a failed diverter is on the high end.

If you're comparing DIY vs. hiring a pro, factor in the cost of your time and the risk of damaging a $300 fixture. For a simple cartridge swap on a modern faucet, DIY makes sense. For anything involving corroded parts, unusual fixtures, or a leak you can't pinpoint, professional leak detection McLean VA and repair is the safer bet.

Common mistakes to avoid

We've seen these mistakes turn a 30-minute repair into a flooded cabinet or a broken fixture.

  • Forcing a stuck handle. If the handle won't budge, you've missed a set screw. Forcing it cracks the handle or strips the stem.
  • Overtightening the packing nut. This crushes the O-ring and causes a leak at the base. Tighten until snug, then a quarter-turn more.
  • Using petroleum-based grease. It degrades rubber O-rings. Use silicone plumber's grease only.
  • Not replacing the O-rings when you replace the cartridge. The old O-rings are just as worn as the cartridge. Replace them together.
  • Ignoring the shutoff valves. If your shutoff valves don't close fully, you'll get water spraying when you open the faucet. Test them before you start.
  • Dropping screws down the drain. Plug the drain. Every time.

One more: don't assume the drip is the faucet's fault. If your toilet repair McLean VA or another fixture is also running, you may have a water pressure issue - typically above 80 PSI - that's stressing every seal in the house. A pressure-reducing valve adjustment solves that.

When to call a professional

Call a plumber when the faucet body is cracked, when the valve seat is pitted, when you can't identify the faucet brand, or when you've replaced the cartridge and the drip persists. Also call if you see water pooling under the sink, if the cabinet floor is soft, or if you smell musty odors - those signs point to a hidden leak that's been running longer than the faucet drip.

Our team handles faucet repair, cartridge replacement, and full fixture swaps across McLean. We carry common cartridges on the truck, so most repairs are done in one visit. If you're in Plumbers McLean VA in McLean Hamlet or anywhere nearby, we can usually get to you the same day.

Frequently Asked Questions

How do I fix a dripping faucet in McLean VA?

Shut off the water supply, remove the handle, pull the cartridge, and replace it with a matching part. Clean the valve seat while you're in there. Reassemble and test. Most drips stop immediately. If the drip continues, the valve seat or faucet body may be damaged.

What causes a faucet to drip in McLean Virginia?

Worn rubber seals, corroded valve seats, and mineral buildup from moderately hard water. McLean's water runs 7-9 grains per gallon, which accelerates deposit formation. Thermal cycling from hot water also hardens rubber over time. Cartridge and ceramic disc faucets fail when sediment scratches the sealing surfaces.

How much does faucet repair cost in McLean VA?

Professional repair runs $150-$350 for a single faucet, including parts. DIY parts cost $8-$35. Faucet replacement with labor runs $280-$700 depending on the fixture. After-hours emergency service starts around $250. These are 2026 ranges for the McLean area.

Can I fix a dripping faucet myself in McLean VA?

Yes, if you have basic tools and can identify your faucet's brand and model. Cartridge and washer replacements are straightforward. Call a pro if the faucet body is cracked, the valve seat is pitted, or you can't find the right part. A failed DIY attempt on a high-end fixture can cost more than the original repair.

How long does a faucet repair take?

A cartridge replacement takes 45-90 minutes for a DIYer and 30-60 minutes for a plumber. Faucet replacement takes 1-2 hours. If corrosion or seized parts slow things down, add another 30 minutes. We carry common cartridges on the truck to avoid a second trip.

Get help with plumbers McLean VA in McLean

If your faucet is still dripping after a cartridge swap, or if you'd rather skip the DIY entirely, we're here. Our licensed plumbers handle faucet repair, cartridge replacement, and full fixture installation across McLean - usually the same day you call.

Call +1 (831) 293-1204 to schedule your faucet repair. We'll confirm the price before we start, and we'll test the faucet with you before we leave.

Tagged with

#faucet repair#diy plumbing#mclean va#dripping faucet#home maintenance

Common Questions

How do I fix a dripping faucet in McLean VA?
Shut off the water supply, remove the handle, pull the cartridge, and replace it with a matching part. Clean the valve seat while you're in there. Reassemble and test. Most drips stop immediately. If the drip continues, the valve seat or faucet body may be damaged.
What causes a faucet to drip in McLean Virginia?
Worn rubber seals, corroded valve seats, and mineral buildup from moderately hard water. McLean's water runs 7-9 grains per gallon, which accelerates deposit formation. Thermal cycling from hot water also hardens rubber over time. Cartridge and ceramic disc faucets fail when sediment scratches the sealing surfaces.
How much does faucet repair cost in McLean VA?
Professional repair runs $150-$350 for a single faucet, including parts. DIY parts cost $8-$35. Faucet replacement with labor runs $280-$700 depending on the fixture. After-hours emergency service starts around $250. These are 2026 ranges for the McLean area.
Can I fix a dripping faucet myself in McLean VA?
Yes, if you have basic tools and can identify your faucet's brand and model. Cartridge and washer replacements are straightforward. Call a pro if the faucet body is cracked, the valve seat is pitted, or you can't find the right part. A failed DIY attempt on a high-end fixture can cost more than the original repair.
How long does a faucet repair take?
A cartridge replacement takes 45-90 minutes for a DIYer and 30-60 minutes for a plumber. Faucet replacement takes 1-2 hours. If corrosion or seized parts slow things down, add another 30 minutes. We carry common cartridges on the truck to avoid a second trip.

Need a faucet fixed today in McLean?

Our licensed plumbers repair dripping faucets, replace cartridges, and install new fixtures across McLean. We confirm the price before we start and test the faucet with you before we leave.

Call +18312931204 Send a Message
Call +18312931204 Get Quote
Call Quote