Unit and Materials
We supply the Rheem, Navien, or AO Smith unit you choose, plus the copper pipe, PEX tubing, pipe fittings, solder, Teflon tape, and vent kit needed to complete the job. Nothing is subcontracted.
Every install we quote covers the unit, the permit, the venting, the gas or electrical hookup, and the final test. If your home needs a gas line upgrade or a new circuit, we price that up front so there are no surprises on install day.
We supply the Rheem, Navien, or AO Smith unit you choose, plus the copper pipe, PEX tubing, pipe fittings, solder, Teflon tape, and vent kit needed to complete the job. Nothing is subcontracted.
We pull the Fairfax County plumbing permit and schedule the inspection. You get the signed-off card when the job closes, which keeps your manufacturer warranty valid.
For gas units, we run and pressure-test the dedicated line. For electric units, we run the 240-volt circuit and confirm your panel has the amperage to carry it.
We drain, disconnect, and haul away your old storage tank, including the sediment and the old fittings. Your utility room is left clean and ready for storage.
We pressure-test every joint, fire the unit, set the outlet temperature, and show you how to isolate and descale it. You get the manual, warranty card, and our direct number.
Tankless water heater installation McLean VA is the licensed removal of your old storage tank and the mounting, venting, gas or electrical hookup, and commissioning of an on-demand unit that heats water only when a tap opens. We run a dedicated gas line or a 240-volt circuit, cut and solder copper pipe or crimp PEX tubing, and pressure-test the whole run before the unit fires. A pipe wrench, pipe cutter, and pressure gauge are on every truck. The result is hot water in about 5 seconds, not 30.
Most McLean homes we walk into are running a 12- to 15-year-old tank in a basement or utility closet, and the homeowner is tired of cold showers after the third load of laundry. A tankless water heater install McLean Virginia solves that, but only if the unit is sized to your flow rate and your gas meter can feed it. We check both before we quote. If you have been searching for tankless water heater installation near me McLean VA, we cover every neighborhood from Chesterbrook to Langley Forest.
You get a written scope, a firm price, and a one-day install in most cases. Here is exactly what happens from the first phone call to the final test, so you know who is in your house and what they are doing.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
RIDGID Pipe Wrench and Pipe Cutter
Used to break down the old tank fittings and cut copper or black iron pipe to length. A clean cut is the difference between a joint that holds for 20 years and one that weeps in year three.
Soldering Torch and Pressure Gauge
We solder copper joints and then pressure-test the entire gas and water run. The gauge holds for 15 minutes before we fire the unit, so a slow leak never makes it past install day.
Milwaukee Cordless Tools
Used for mounting brackets, vent penetrations, and cutting PEX tubing. Cordless means no extension cords across your finished basement floor.
Leak Detection Equipment
We check the old supply lines and the new connections for hidden leaks. If we find a slab leak or a pinhole in the copper, we flag it before the new unit goes in.
Sewer Camera
Not every install needs it, but when a utility room shares a wall with a floor drain, we run the camera to confirm the drain is clear before we mount anything.
Manual J Load Sizing
We calculate your peak hot water demand based on bathroom count, fixture flow rates, and incoming water temperature. McLean's incoming water runs about 50 degrees in winter, which affects the unit's flow capacity. Sizing to the real number, not a rule of thumb, is what prevents cold-water surprises.
Fairfax County Plumbing Code Compliance
Every install follows the Virginia Uniform Statewide Building Code and Fairfax County amendments, including vent termination clearances, gas line sizing, and T&P relief valve placement. We pull the permit and meet the inspector on site.
Concentric and PVC Venting
We use the manufacturer's concentric vent kit or schedule 40 PVC, depending on the unit and the wall penetration. Vent length and elbow count are calculated against the installation manual, not guessed.
Isolation Valve and Descaling Port Setup
Every unit we install gets isolation valves and a descaling port on the cold inlet. That turns annual maintenance into a 45-minute job instead of a half-day teardown.
01
What we do: We install a 199,000 BTU Navien unit with a recirculation loop so hot water reaches the far bathroom in seconds. The recirculation pump runs on a schedule, not constantly.
→ Three showers, two sinks, and the dishwasher run at once without a temperature drop. The morning rush stops being a negotiation.
02
What we do: We mount a Rheem unit on the wall above the old tank footprint, run a concentric vent through the existing roof penetration, and free up the floor space.
→ The homeowner gains a 2-foot by 2-foot storage area and gets a unit with a 10-year warranty instead of a 6-year tank.
03
What we do: We measure static pressure and flow, then install a 160,000 BTU unit sized to the meter's capacity, or coordinate a meter upgrade with Washington Gas if the homeowner wants the larger unit.
→ The unit runs at full capacity without starving the furnace or the range. No mid-shower temperature swings.
04
What we do: We install an AO Smith unit with isolation valves and a descaling port, then set up an annual service reminder for the property manager.
→ The owner avoids a mid-lease tank failure and gets a unit that lasts through two tenant cycles instead of one.
McLean sits in Fairfax County, and the housing stock ranges from 1950s colonials in Salona Village to new builds in Langley Forest. Older homes often have undersized gas lines and 100-amp panels, which means we check meter capacity and amperage before we quote a unit. Incoming water temperature drops to about 50 degrees in January, so we size for winter, not summer. If you are comparing tankless vs tank water heater cost McLean VA, the up-front difference is real, but the 20-year service life and lower gas use close the gap. We pull the Fairfax County permit on every job, and we install whole house tankless water heater McLean Virginia systems that pass inspection the first time. Whether you are in 22101 or 22043, we can usually be on site the same day.
Chesterbrook
Many homes here have finished basements with the water heater in a closet. Wall-mounting a tankless unit frees that floor space and keeps the unit out of flood range.
Langley Forest
Larger homes with four or more bathrooms often need a 199,000 BTU unit and a recirculation loop to keep hot water at the far fixtures.
Salona Village
1950s colonials with 100-amp panels and older gas meters. We check capacity before recommending a unit size.
Downtown McLean
Tighter lots and older utility rooms. We plan the vent path before install day so we are not cutting into a finished ceiling.
Winter incoming water temperature near 50 degrees
Cold inlet water reduces a tankless unit's flow rate. We size for January conditions so you are not short on hot water when you need it most.
Older homes with undersized gas lines
A 1/2-inch line cannot feed a 199,000 BTU unit. We measure static pressure and either run a dedicated 3/4-inch line or size the unit to the existing supply.
Fairfax County permit and inspection requirements
Every tankless install needs a plumbing permit and a gas or electrical inspection. We handle the paperwork and meet the inspector, so the job closes clean.
Hard water in the Potomac watershed
Mineral content builds scale in the heat exchanger. We install isolation valves and a descaling port on every unit and recommend annual service.
Most homeowners call us after a specific failure, not because they want new technology. Here are the four problems we hear most often in McLean, and how a tankless unit fixes each one.
Problem
A 50-gallon tank empties in about 15 minutes when two showers and the laundry run at once. The second person gets a cold rinse, and the tank needs 30 minutes to recover.
Our Fix
We size a tankless unit to your peak flow rate, usually 9 to 11 gallons per minute. It heats water as it moves, so the supply never runs out no matter how many fixtures are open.
Problem
Sediment builds up on the tank floor, trapping heat and causing popping. Rust in the water means the lining has failed, and a leak is weeks away, not months.
Our Fix
We drain and remove the failing tank, inspect the supply lines for corrosion, and install a tankless unit with a sediment filter. No tank means no sediment layer and no rust-colored water.
Problem
A leaking tank can dump 40 gallons on your floor before you notice. In a finished basement, that means ruined drywall, carpet, and sometimes a mold problem.
Our Fix
We shut off the supply, use leak detection equipment to confirm the tank is the source, and replace it with a wall-mounted tankless unit. Nothing sits on the floor, so a future leak cannot pool in your basement.
Problem
A storage tank keeps 40 to 50 gallons hot around the clock, even when nobody is home. That standby loss can account for 20 to 30 percent of your water heating bill.
Our Fix
A tankless unit fires only when a tap opens. We set the outlet temperature to 120 degrees and confirm the gas line is sized correctly, so you pay for heat you actually use.
A tankless unit costs more up front than a tank, and it pays that back in lower gas use, freed-up floor space, and a service life that runs 20 years instead of 10. Here is what changes in your house the week we install it.
Endless Hot Water
A 199,000 BTU Navien unit delivers about 11 gallons per minute, enough for two showers and the dishwasher at once. No more waiting 30 minutes between loads. For a family of five in McLean Hamlet, that alone justifies the switch.
Lower Gas Bills
Tanks keep 40 to 50 gallons hot 24 hours a day whether you use it or not. A tankless unit fires only on demand, cutting standby loss by up to 30%. Most Fairfax County homeowners see $15 to $30 a month come off the gas bill.
20-Year Service Life
Storage tanks rust from the inside and fail at 10 to 12 years. Tankless heat exchangers carry 10- to 15-year warranties and last 20 years with annual descaling. That is one replacement instead of two.
Reclaims Floor Space
A wall-mounted unit is about the size of a carry-on suitcase. It frees up a 2-foot by 2-foot footprint in your utility room, which matters in the older, tighter basements common in Salona Village and Franklin Park.
Typical 2026 pricing for tankless water heater installation in this area runs $3,200 to $5,800, depending on the unit, the venting, and whether your home needs a gas line or electrical upgrade. A straight swap on an existing gas line sits near the low end. Adding a dedicated line, a meter upgrade, or a 240-volt circuit pushes toward the top. We quote a firm number after sizing your home, so you are not comparing a guess to a guess.
Typical Investment Range
$3,200 - $5,800 depending on unit, venting, and gas or electrical work
A tankless unit costs more up front than a tank, but it lasts 20 years instead of 10 and cuts standby heat loss by up to 30 percent. For most McLean families, the gas savings and one avoided replacement pay back the difference.
What changes the price
Unit Size and Brand
A 160,000 BTU unit costs less than a 199,000 BTU model. Rheem, Navien, and AO Smith units sit at different price points, and the right one depends on your bathroom count and peak flow rate.
Gas Line or Circuit Work
If your existing gas line is undersized, we run a dedicated 3/4-inch line. Electric units need a 240-volt circuit and enough panel amperage. Both add labor and materials.
Vent Length and Type
A short concentric vent through an exterior wall is straightforward. A long PVC run with multiple elbows costs more in materials and labor, and the manufacturer's manual sets the limit.
Permit and Inspection
Fairfax County requires a plumbing permit and an inspection on every tankless install. The fee is part of the quote, not a surprise line item later.
Old Tank Removal
Draining and hauling off a 50-gallon tank is included in our quotes. If the old unit is in a crawlspace or behind a finished wall, access adds time.
Google ★★★★★4.9
Installed a Navien tankless unit in our McLean home. They pulled the permit, handled the inspection, and walked us through the descaling process. Clean work, fair price, and hot water never runs out.
Yelp ★★★★★4.8
Our old tank started leaking on a Friday. They came out the same day, confirmed the tank was the issue, and installed a wall-mounted unit by late afternoon. No basement damage, no drama.
BBB ★★★★★4.9
Third quote we got, and the only one that checked our gas meter capacity. They ran a new line and installed a unit sized for our four bathrooms. Two years in, zero issues.
Google ★★★★★5.0
Professional from the first call. They explained the difference between gas and electric units, quoted a firm price, and finished in one day. The utility room is cleaner than they found it.
Our team holds Virginia DPOR plumbing licenses, including Master Plumber and Journeyman credentials, and we carry backflow prevention certification and OSHA safety training. We install Rheem, Navien, Bradford White, and AO Smith units, and we service what we sell. Because we also run drain cleaning and leak detection calls across McLean, we know how these houses are plumbed before we open a wall. That local experience is why our installs pass Fairfax County inspection the first time.
Real experiences from customers who chose our Tankless Water Heater Installation services.
“Our 14-year-old tank finally quit on a Sunday. They came out Monday morning, sized a Navien unit for our four bathrooms, and had it running by 3 p.m. The permit and inspection were handled without me lifting a finger. Gas bill dropped $22 the first month.”
Sarah M.
Homeowner, Chesterbrook
“I got three quotes for tankless. These guys were the only ones who checked my gas meter capacity before quoting. The other two would have sold me a unit my meter could not feed. Install was clean, copper work was tight, and they walked me through the descaling ports.”
David L.
Homeowner, Langley Forest
“We were tired of cold showers when the dishwasher ran. They installed a Rheem unit in about five hours and set the temperature to 120. Two showers and the laundry at once now, no problem. They even hauled off the old tank and swept the utility room.”
Priya R.
Homeowner, McLean Hamlet
Real answers to the questions we hear most often from local homeowners and property managers.
If your old tank lets go at 2 a.m., we shut off the water, contain the damage, and get you on the schedule for a tankless replacement. One call handles the emergency and the upgrade.
View Emergency PlumbingA clogged drain and a failing water heater often show up the same week. We clear the line with a drain snake or hydro jetter, then size your tankless unit while we are already on site.
View Drain CleaningNot every tank needs replacing. If your unit is under 10 years old, we diagnose the issue with a pressure gauge and leak detection equipment, and repair it if the fix makes financial sense.
View Water Heater RepairIf tankless is not the right fit for your home, we install and warranty traditional tank units from Bradford White and AO Smith. Same permit process, same one-day turnaround.
View Water Heater InstallationA hidden slab leak or pinhole in copper pipe can mimic a water heater problem. We use leak detection equipment to find the source before we install anything, so the new unit is not masking a bigger issue.
View Leak DetectionFrozen pipes in a McLean winter can split copper overnight. We repair the burst section, check the rest of the run, and make sure your new tankless unit has a sound supply line.
View Burst Pipe RepairCall us at +1 831-293-1204 or email [email protected]. We answer the phone 24/7, including weekends and holidays. Our dispatcher will confirm your address in McLean, give you an arrival window, and send a licensed tech with a fully stocked truck. Same-day appointments are usually available.
Phone
+18312931204Address
942 Dead Run Dr, McLean, VA 22101
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available